Put the "ing" in your Boating

Call: 519-538-2887

Call: 1-519-538-2887

captain-wheelErnst asks “How do I find the centre of my wheel when docking my Twin Inboard?

I must use the wheel hard over as well as using the shifts, because it is so windy and I can never get the wheel back to centre.

Then the boat doesn’t go where I expect.

Even though Ernst has a Twin Inboard, this article applies to all drive systems—power and sail.

 

Positioning the Wheel

Top dead centre” is the position of the wheel that allows you to steer your boat straight with no back and forth movement of the wheel. When the boat is moving straight, your drive(s) or rudder(s) is/are straight.

Positioning your wheel to steer straight, compensates for and overrides all the torque, prop walk, skeg, rudder size and other “tech stuff “. You don’t have to worry about any of that. It is all compensated for during the locating of “top dead center” of your wheel on all drive systems.

Do you understand and could you explain technically how your car’s ABS brakes work? Not likely. You just know that your car will stop straight, when you stomp on the brake pedal!

The tiller on a sailboat is connected directly to the rudder, as is the handle on a tiller operated outboard fishing boat. A quick glance will tell you whether it is straight or not. But, on inboards and sterndrives, you sit at the wheel and can’t see the rudder(s) or drive(s), so you don’t know whether they are straight or not.

Why is it important?

When docking your boat, it is very important to know where “top dead centre” is, so that you know exactly where your boat is going to go within the confines of the fairway and slip. When you shift gears within your slip, you want your boat to head in the direction you expect—no surprises, no disappointments.

Here is a simple tip that will help you bring the wheel back to “top dead centre” when docking, so that when you are in neutral and coasting or when you return to forward you are going straight ahead or when you return to reverse, you are going straight back. This is a necessity when docking.

How can you find it?

I suggest the easiest and simplest way to find “top dead centre” on your wheel, is as follows:

  • On a perfectly calm day in open water, set both motors at exactly the same rpm, say 800. (If the wind never stops blowing, just aim directly down wind at a landmark.)
  • Then idle toward a landmark on the shoreline.
  • Adjust the wheel slightly until the boat is tracking perfectly straight.
  • Mark top dead centre of the wheel with a piece of black electrical tape.
  • Once you have “top dead centre” marked on your wheel, use it to recover your straight ahead direction after executing a tight turn in tight quarters in the harbor or at your slip, rather than counting 2 1/2 turns or whatever back from hard over.

How I do it

When I dock a boat, I place my left hand on the wheel at “top dead centre” and never remove it. (Mentally, duct tape your left hand to the electrical tape spot on the wheel). I run the shift(s) with my right hand and “palm” the wheel with my left hand (not hand over hand). Then, my hand is always in the same spot. As I put it, my left hand “remembers” where it has to come back to, to steer straight. It may be 1 full turn or 2 full turns or part of a turn depending on how many rotations I had previously turned.

When it is windy, I turn the wheel toward the wind 1/8 or ¼ turn depending on how windy it is, to counteract the force of the wind to keep going straight. (Lean into the wind)

On boats with dual helms (flybridge and cabin) with wheels that don't turn at the same time, I leave the wheel centred each time I leave. Then, when I return to that helm, I know I am starting from top dead centre. When our grandkids or guests are aboard, I have to check each time because they love to turn the wheel.

New idea?

wheel-with-braid-top-dead-centerYou may think this is a new idea, but far from it. Way before my great, great grandfather was building boats on the Thames in London England, Captains devised a method of marking “top dead centre” on the wheels of sailing ships, ocean going freighters and cruise ships.

Back then, the wheels were wooden with spokes. One method was to splice a cord donut and pull it tightly over the spoke of the ship’s wheel that was “top dead centre”.

In the picture, a cord is wrapped and tied around the top interior spoke. On some ships, that spoke was made of a different coloured wood than all the other spokes. Other ship’s wheels had extra grooves on the top spoke, when it was turned in the lathe. As a result, the helmsman could feel the “top dead centre” spoke. Whoever the helmsman was, he knew which spoke had to be up, to be sure the rudder was dead straight and he was steering straight.

You may be more familiar with the dimples on a calculator or a keyboard or phone that let you know your fingers are in the right place.

modern-wheel-2Today, the wheels on recreational boats are round with no markings. The support bars don’t necessarily mean anything, as far as steering straight is concerned. I have suggested black electrical tape, because to other people it is invisible and disappears. Nobody sees it but you (unless you point it out), not even “the old salty know-it-all from down the dock”.

You may come up with something more elaborate to help you instantly identify “top dead centre”. Go for it!

Try it and let me know how much easier docking is for you.

 

Share your suggestions below in comments.

Doug Dawson

 

See: Docking Lessons

Also read “Why Docking is so difficult

Comments (3)

This comment was minimized by the moderator on the site

What do you do if you have duel helms (flydeck and cabin) and both wheels do not turn at the same time?

This comment was minimized by the moderator on the site

I wonder if the term "top knot" evolved from the practice of wrapping cord around the top of the spokes.

This comment was minimized by the moderator on the site

Hi Doug,<br />Thanks for those precious comments. I have already marked my wheel. The point was the fact to leave the hand at the same point and use the intuitive motion. Be sure that I'll be one of your good students-captains. And soon, I'll...

Hi Doug,<br />Thanks for those precious comments. I have already marked my wheel. The point was the fact to leave the hand at the same point and use the intuitive motion. Be sure that I'll be one of your good students-captains. And soon, I'll come with my family to Canada to meet with you and your wife. Sure in July. <br />Respectfully,<br /><br />Ernst<br /><br />N.B . For flydeck and cabin, I think ; either both wheels should be mechanically synchronized at the same time, or have for each one its own mark for dead center. In all conditions (in cabin or flybridge) the boat will go straight.

Read More
There are no comments posted here yet

Leave your comments

  1. Posting comment as a guest. Sign up or login to your account.
0 Characters
Attachments (0 / 3)
Share Your Location

FREE Special Report:
7 Steps To Buying The Right Boat


My Cart

The cart is empty